When a Mokena homeowner calls us about water near the chimney, the flashing is the first thing we look at — it is the most common leak point on the entire system and the trickiest for a homeowner to read.
What Flashing Is and Why It Fails
Flashing is the system of thin metal sheets that bridges the gap where the chimney passes through the roof. It is not a single piece but a layered assembly: base flashing bent up against the brick, step flashing woven into the shingles, and counter flashing tucked into the mortar joints to shed water over the top. Done well, it channels rain away from that vulnerable seam. Done poorly — or simply aged — it becomes the easiest path for water to slip under the roof.
Flashing fails for predictable reasons. The metal corrodes over decades, the sealant at the counter-flashing line dries and cracks, fasteners loosen, and the whole assembly shifts slightly as the roof and chimney expand and contract through Illinois temperature swings. Many leaks we trace are not even corrosion; they are a tar-and-seal patch job from a previous owner that has long since given up. A reroof is another common trigger — when old shingles come off, the step flashing is sometimes reused or reinstalled carelessly, leaving gaps that only reveal themselves during the first hard, wind-driven rain afterward.
Signs You Can Spot From Inside
Most homeowners notice a flashing leak from indoors first, often blaming the roof or the chimney itself. Walk the top floor and attic and look for these clues:
- Brown or rust-colored stains on the ceiling or wall near the chimney chase.
- Peeling paint or bubbling drywall on the chimney surround.
- A damp, musty smell in the attic concentrated around the chimney penetration.
- Visible water tracks or daylight where the chimney meets the roof deck, seen from inside the attic.
- Staining that appears only after wind-driven rain, a classic flashing signature.
The telltale pattern is that the water shows up near — but not always directly below — the chimney, because it travels along framing before it drips. That wandering is exactly why flashing leaks get misdiagnosed: a stain two feet from the chase makes a homeowner suspect a plumbing line or a roof valley, when the water actually entered at the chimney and simply ran downhill along a rafter before it found a place to fall.
Signs You Can Spot From Outside
If you can safely view the roofline from a window or the ground with binoculars, a few exterior signs point straight at the flashing. Look for metal that is lifted, curled, or pulling away from the brick rather than lying flat. Check whether the counter flashing still sits firmly in the mortar joint or has slipped out, leaving a gap. Rust streaks running down from the flashing line signal corroding metal, and a thick smear of black roofing tar is a warning that someone already tried — and failed — to patch a leak here. A proper chimney inspection confirms the cause without guesswork, because flashing problems are routinely mistaken for crown or cap failures.
Why Flashing Leaks Need Prompt Attention
A flashing leak rarely stays a flashing problem. Water that gets past the seam soaks roof decking, rots framing, and runs down into the masonry, where it accelerates freeze-thaw damage from the inside out. By the time a ceiling stain appears, the water has usually been working for a while. Our chimney repair work rebuilds the flashing as a layered, mechanically sound assembly rather than a surface patch, and we cut fresh counter flashing into the mortar so it sheds water the way the original design intended. We follow the NFPA 211 standard on every visit, documenting what we find so you see the full picture. Homeowners throughout our Mokena service area count on that honest diagnosis to fix the actual leak instead of chasing the stain.
Frequently asked questions
How can I tell a flashing leak from a crown leak?
Flashing leaks usually show up at the roofline and worsen with wind-driven rain, while crown leaks tend to track straight down the flue. An inspection distinguishes them reliably, since the symptoms overlap from inside the house.
Can I just seal the flashing with roofing tar?
Tar is a temporary stopgap at best and often hides a worsening problem. It cracks within a season or two, and we frequently find failed tar patches behind leaks that could have been properly repaired.
Does new flashing require roof work?
Rebuilding flashing involves integrating metal with the surrounding shingles and mortar, so it touches both the roof and the masonry. Doing it correctly means addressing both, not just the chimney side.
Why does my leak only appear sometimes?
Flashing gaps often leak only when rain is driven at a certain angle by wind. That intermittent pattern is actually a strong clue that flashing, rather than a constant source, is the culprit.
Could the leak be coming from the chimney cap instead?
It can, which is why we check the whole water-shedding system. Caps, crowns, and flashing all protect against water, and a thorough inspection pinpoints which one is letting it in.
How urgent is a small flashing leak?
More urgent than it looks. Even minor intrusion rots decking and framing and feeds masonry deterioration, so addressing it early prevents a far larger structural repair later.
Published November 15, 2026.
